*Heading
 :  cgax6mh Model Change Verification, Hyperelastic Material
*Node,Nset=Short1
 2,2.,0.5
 202,1.,0.5
 402,0.0,0.5
*Node,Nset=Short2
 10,2.,4.5
 210,1.,4.5
 410,0.0,4.5
*Nfill,Nset=Short
 Short1,Short2,4,2
*Node
 1,2.
 11,2.,5.
 401,
 411,,5.
*Ngen,Nset=Rhs
 1,11,1
*Ngen,Nset=Lhs
 401,411,1
*Nfill,Nset=Nall
 Rhs,Lhs,4,100
*Nset, Nset=Yfix, Gen
 1, 401, 100
*Nset, Nset=Xfix
 1, 
*Nset, Nset=Xfix2
 11, 
*Nset, Nset=Ymove, Gen
 11, 411, 100
*Nset, Nset=Xmove, Gen
 204, 208, 1
 4, 8, 1
*Nset, Nset=Xmove, Gen
 104, 108, 1
 304, 308, 1
 404, 408, 1
*Element,Type=cgax6mh,Elset=Eall
 1  ,1,3,201, 2,102,101
 101,201,3,203, 102,103,202
*Elgen,Elset=Eall
 1,5,2,1,2,200,5
 101,5,2,1,2,200,5
*Elset, Elset=Eremov
 2,3,4,7,8,9,
 102,103,104,107,108,109
*Solid Section,Material=Rubber,Elset=Eall
 1.,
*Material,Name=Rubber
*Hyperelastic, N=1
 56.00e4, 14.00e4, 1.43e-5
*Conductivity
 1., 
*Boundary
 Ymove, 5, 5
 Yfix, 2, 2
 Yfix, 5, 5
*Initial Conditions, Type=Temperature
 Nall,0.0
**
*Step,Nlgeom
 Step 1: Compress Elements
*Static
 0.1,1.,0.1,0.1
** Control parameters needed for ABAQUS QA purposes only
*Controls,Parameters=Field
 1.E-6,,,1.,,1e-10
*Boundary
 Ymove, 2,2 ,-0.1
*Node Print,Freq=999
 U, 
 Rf, 
*El Print,Freq=999
 E, 
 S, 
*Node File,Freq=999
 U, Rf
*El File,Freq=999
 E, Ne, S
*Output, Field, Freq=999
*Element Output
 Hfl, E, S
*Node Output
 Rf, U
*End Step
**
*Step,Nlgeom
 Step 2: Remove Middle Elements
*Static
 1.,1.
*Model Change,Remove,Type=Element
 Eremov,
*End Step
**
*Step,Nlgeom
 Step 3: Move Top Edge Down
*Static
 1.,1.
*Boundary
 Xmove, 1,1, 0.0
*End Step
**
*Step,Nlgeom
 Step 4: Add Elements Back In
*Static
 0.1,1.,0.1,0.1
*Model Change,Add,Type=Element
 Eremov,
*Boundary,Op=New
 Yfix, 2, 2
 Yfix, 5, 5
 Ymove, 2,2 ,0.1
*End Step